Posted on

Model NO.: SWD
Screw Channel Structure: Deep Screw
Exhaust: Don′t Exhaust
Automation: Automatic
Computerized: Computerized
Trademark: siweida
Transport Package: Export Standard
Specification: Pipe Diameter 16mm-800mm
HS Code: 84778000
Model NO.: SWD
Screw Channel Structure: Deep Screw
Exhaust: Don′t Exhaust
Automation: Automatic
Computerized: Computerized
Trademark: siweida
Transport Package: Export Standard
Specification: Pipe Diameter 16mm-800mm
HS Code: 84778000
PVC tube extrusion line
PVC Pipe Extrusion Production Line

1) Uses SJSA double screw extruding machine as the main machine, assistant machinery: Vacuum spray shape fitting box, three-track hauling off machine, cutting machine, belling machine
2) Can produce pipe in the range: 20 - 630mm
3) Pipe is widely used in water transfer or ejection
4) Using kinds of moulds, this line can produce large range of pipes
5) We can change production line according to requests and provide technology supply if needed
φ 20-φ 110 PRODUCTION LINE TECHNICAL DATA
 
( φ 20 φ 110) Mai n Units Vacuum spray bath Two caterp ill ars haul-offs Cut-offs Stacker
Outli n e deme n sio n 6000 × 830 × 1290 2240 × 1000 × 1600 2000 × 1650 × 2700 5000 × 1200 × 1000
Total power 10.05 2.2 1.5 0
Total Weigh 1000 1000 400 100
 
 
φ 63-φ 250PRODUCTION LINE TECHNICAL DATA
Mai n Units Vacuum spray bath Three caterp ill ars haul-offs
Saws		 DSLKB2550
DSLKB2550Belling - machi n es
(mm) Outli n e deme n sio n 6440× 740× 1550 2680× 1420× 1850 2100× 1200× 1550 7712× 1320× 1900
(KW) Total power 12.77 4 2.2 12.09
KG) Total Weigh 1030 2320 1000 2800

 
 
φ 160-φ 400PRODUCTION LINE TECHNICAL DATA
( φ 160 - φ 400) Mai n Units Vacuum spray bath Spray bath  Four caterp ill ars haul-offs Planetary cut-offs DSLKA4020 Belling - machi n es
mm) Outli n e deme n sio n 6000× 1320× 1610 6000× 1320× 1610 2675× 1540× 1700  3200× 1450× 2300  7800× 2360× 2329 
(KW) Total power 14.35 4 5.5 6.7 22
(KG) Total Weigh 1480 1150 2600 2400 6000
 
 
φ 315-φ 630 PRODUCTION LINE TECHNICAL DATA
( φ 315 - φ 630)
Mai n Units		 Vacuum spray bath Spray bath  Six caterp ill ars haul-offs
Planetary cut-offs		 DSLK6330 Belling - machi n es
(mm) Outli n e deme n sio n 6000× 1510× 1640 6000× 1510× 1640 4000× 2300× 2000 3500× 1950× 2450  8710× 3260× 2800 
(KW) Total power 16.45 5.5 5.5 7.5 36.2
(KG) Total Weigh 2500 1000 2500 3500 6800


 
Single Screw Extruder Vs Twin Screw Extruder

Single Screw Extruder Vs Twin Screw Extruder
Single Screw Extruder Vs Twin Screw Extruder
Single Screw Extruder Vs Twin Screw Extruder
Single Screw Extruder Vs Twin Screw Extruder
Single Screw Extruder Vs Twin Screw Extruder

  PVC tube extrusion line
PVC Pipe Extrusion Production Line

1) Uses SJSA double screw extruding machine as the main machine, assistant machinery: Vacuum spray shape fitting box, three-track hauling off machine, cutting machine, belling machine
2) Can produce pipe in the range: 20 - 630mm
3) Pipe is widely used in water transfer or ejection
4) Using kinds of moulds, this line can produce large range of pipes
5) We can change production line according to requests and provide technology supply if needed
φ 20-φ 110 PRODUCTION LINE TECHNICAL DATA
 
( φ 20 φ 110) Mai n Units Vacuum spray bath Two caterp ill ars haul-offs Cut-offs Stacker
Outli n e deme n sio n 6000 × 830 × 1290 2240 × 1000 × 1600 2000 × 1650 × 2700 5000 × 1200 × 1000
Total power 10.05 2.2 1.5 0
Total Weigh 1000 1000 400 100
 
 
φ 63-φ 250PRODUCTION LINE TECHNICAL DATA
Mai n Units Vacuum spray bath Three caterp ill ars haul-offs
Saws		 DSLKB2550
DSLKB2550Belling - machi n es
(mm) Outli n e deme n sio n 6440× 740× 1550 2680× 1420× 1850 2100× 1200× 1550 7712× 1320× 1900
(KW) Total power 12.77 4 2.2 12.09
KG) Total Weigh 1030 2320 1000 2800

 
 
φ 160-φ 400PRODUCTION LINE TECHNICAL DATA
( φ 160 - φ 400) Mai n Units Vacuum spray bath Spray bath  Four caterp ill ars haul-offs Planetary cut-offs DSLKA4020 Belling - machi n es
mm) Outli n e deme n sio n 6000× 1320× 1610 6000× 1320× 1610 2675× 1540× 1700  3200× 1450× 2300  7800× 2360× 2329 
(KW) Total power 14.35 4 5.5 6.7 22
(KG) Total Weigh 1480 1150 2600 2400 6000
 
 
φ 315-φ 630 PRODUCTION LINE TECHNICAL DATA
( φ 315 - φ 630)
Mai n Units		 Vacuum spray bath Spray bath  Six caterp ill ars haul-offs
Planetary cut-offs		 DSLK6330 Belling - machi n es
(mm) Outli n e deme n sio n 6000× 1510× 1640 6000× 1510× 1640 4000× 2300× 2000 3500× 1950× 2450  8710× 3260× 2800 
(KW) Total power 16.45 5.5 5.5 7.5 36.2
(KG) Total Weigh 2500 1000 2500 3500 6800


 
Single Screw Extruder Vs Twin Screw Extruder

Single Screw Extruder Vs Twin Screw Extruder
Single Screw Extruder Vs Twin Screw Extruder
Single Screw Extruder Vs Twin Screw Extruder
Single Screw Extruder Vs Twin Screw Extruder
Single Screw Extruder Vs Twin Screw Extruder

 

1. What is a Semi Tipper Trailer?

Tipper Semi Trailer are also called dump trucks, dumper trailer, side tipper, tip trailer, scrap  Dump Trailer .

In civil engineering, it often works in conjunction with excavators, loaders, belt conveyors and other Construction Machinery. The dump trailer carriage adopts rear-dump and side -dump self-unloading methods, which improves the efficiency of the bulk cargo transport by the loader. The semi truck trailer tipper carriage is inclined at a certain angle, so that the cargo in the carriage is unloaded. The power of the Dump Truck Trailer engine is used to complete the dumping mechanism.


2. What are the common types of dump trailers?

There are four types of tipper Semi Trailer : rear tipping semi trailers, side rock Dump Semi Trailer , skeleton dump trailer, and flatbed type tipping trailer.

What are the tonnages of hydraulic dump trailer?

The tilt chassis trailer manufacturer`s hydraulic dump trailer can be customized from 15 tons to 80 tons, 80 tons to 120 tons,  120 tons-180 tons of different tonnage according to the different cargoes.

The volume of the tipper semi trailer can be customized according to the needs of the customers. The common volumes are 30 cubic meters, 32 cubic meters, 35 cubic meters, 45 cubic meters, 50 cubic meters, 60 cubic meters, 80 cubic meters and so on. Such as 15m and 20m3 tipper trailer for sale.

 

3. CHVM dump tipper semi trailers transportation

To prevent the tipper semi trailer paint from being corroded by seawater, we spray a layer of wax on the surface of the dump trailer before shipping, and then seal it with a waterproof rain cloth.


4. Components of the hydraulic lifting system of end dump trailer

The rear tipping semi-trailer train is mainly composed of a tractor and a semi-trailer. The tractor is connected by a saddle and a semi-trailer to form a semi-trailer train. The rear dump trailer hydraulic lift system is mainly composed of power take-off (transmission), hydraulic pump, lift valve, pneumatic control valve, limit valve, hydraulic cylinder, hydraulic oil tank, high (low) pressure oil pipe and so on.

Rear trailer hydraulic lifting principle: Operate the tractor tipper trailer transmission power take-off device to drive the hydraulic pump.The hydraulic pump sucks the hydraulic oil in the hydraulic oil tank through the low-pressure oil inlet pipe and generates high-pressure oil for output.

The high-pressure oil output by the gear pump enters the poppet valve through the high-pressure oil pipe.

The lift valve sends high pressure oil to the oil cylinder or discharges it into the hydraulic oil tank under the control of the air control valve, thereby achieving the functions of lifting, stopping and lowering the hydraulic oil cylinder.


5. Operating instructions of the hydraulic lifting system of end dump trailer

(1) CHVM lifting 20/28ft adjustable custom container chassis trailer hydraulic system lifting operation sequence: Open the tarpaulin or box lid on the trailer--Open the rear door lock--Press the clutch with the transmission in neutral and wait 5 seconds--Hanging low gear (below 4 gears)--Place the handle of the air control valve in the raised position--The dump trailer starts to lift after releasing the clutch, The engine throttle can be properly depressed but it must be controlled within 1500 rpm-when the cylinder reaches the maximum stroke or the limit valve is activated, the air control valve handle is in the stop position.

(2) Rear tipping trailer descending operation sequence: Step on the clutch and wait 5 seconds--Adjust PTO--Adjust transmission gear--Release the clutch--Turn the handle of the air control valve slowly from the stop position to the down position--When you fully lower the car body, wait for 30 seconds and put the handle of the air control valve in the stop position.

6. Precautions for operating the hydraulic lifting system of heavy duty dump trailers

(1) The hydraulic tank of the Titan end dump trailer auction is a special lifting cylinder. Don`t use the cylinder as a stable support for the dump trailer body.

(2) Do not leave the cylinder exposed to the air for more than 2 hours (more than 30 minutes in humid air) in a lifted state, otherwise it will cause oxidation and rust of the cylinder;


(6) During the lifting operation, the operator cannot leave the operating position, and no one can stand or walk in the vicinity of the work area;

(7) During the lifting operation,  the operator must pay attention to the influence of lateral wind, because the long body of the dump semi-trailer will cause the dumper trailer to roll over under the effect of lateral wind;

(8) Don`t make the height of the cargo exceed the back door. Be sure to open the rear door locking device before lifting and unloading, otherwise the cargo will be crowded at the rear of the tractor tipping trailer and the vehicle will tip over when unloading;

(9) When unloading at temperatures below 0 degrees, it is important to pay attention to whether the cargo frozen, otherwise the rear dump semi trailer will roll over due to imbalance between left and right when unloading;

(10) Do not move the dump tipper while the dump trailer is in the lifted state, and don`t use the emergency braking method to unload sticky goods, otherwise it will cause the tractor tipping trailer to roll over or damage the oil tank;

(11) If the lifting angle of the box reaches about 25 degrees, and the cargo in the box has not been unloaded, please stop lifting and check the cause of stickiness;

(12) If the anticipation that a rollover may occur during lifting, be sure to stop lifting and drop the tipper semi trailer slowly;

(13) Wait for about 30 seconds after the schmitt dump tipper body completely lower. Make sure to keep the handle of the air control valve in the stop position. Do not start the heavy duty dump trailer in the lowered position. Do not drive the dump trailers in the lowered position. Otherwise, all the hydraulic oil in the hydraulic cylinder will flow back into the hydraulic tank, causing cavitation and Fuel injection problem.

 

7. Maintenance Specifications for rock dump trailer Hydraulic Lifting System

(1) The new hydraulic dump trailer should be slowly raised during the running-in period. In principle, we should control the engine speed at about 1000 rpm, and it should not exceed 1500 rpm after the running-in period;

(2) Due to the existence of impurities such as iron filings in the hydraulic system during the running-in of the semi dump trailers, when the side tipper trailer is lifted about 300 times, we should replace the hydraulic oil and clean the hydraulic oil box in time;

(3) The high pressure oil pipe must be replaced every two years. In daily maintenance, if you find that the hose is leaking, damaged or partially swollen or cracked, you should replace it in time;

(4) Check the hydraulic oil for discoloration or deterioration every week. If there is any discoloration or deterioration, replace the hydraulic oil in time. Change the oil according to different regions and seasons. Generally, it is more appropriate to change the oil in April and October. When you find that the fuel is insufficient, you should add it in time.

(5) The upper and lower brackets of the oil cylinder need to be filled with grease (butter) in time. It is recommended that the oil cylinder be filled with grease once every 120 times or 15 days. After a long period of non-use, you need to refill the grease once again;

(6) Check the oil return filter element and air filter element inside the hydraulic oil tank for debris clogged and cleaned every half month, and replace the hydraulic oil tank return filter element and air filter element every six months.


(3) It is forbidden to disassemble and adjust the relief valve on the lift valve, otherwise the hydraulic system will lose its safety protection function and cause an accident.

(4) When the dump truck load cargo, we should ensure that the front and back and left and right loading are uniform. If you have too much cargo in front, it can overload the hydraulic system.Too much cargo is loaded behind the trailer, which will cause the vehicle to tip over when unloading, and the left and right partial load will easily cause the cylinder to tip over.

(5) When unloading, please make sure that the ground around the light weight tip trailer is solid and flat, keep the triple axle dump trailer stable, and ensure that the main dump truck and the Scrap Tipper Trailer are in a straight line;




Tipper Semi Trailer

Tipper Semi Trailer,Semi Tipper Trailer,Dump Trailer,Rear Dumper Semi Trailer

Liangshan Changhong Special Purpose Vehicle Manufacturing Co., Ltd. , https://www.chvehicles.com